Power: 2500 watts max X 1 @1-ohm, 1250 watts max X 1 @2-ohms, 625 watts max X 1 @4-Ohms
Class D: power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until it’s needed instead of being converted into heat. Reduction in size/weight, reduced power waste, smaller heat sink, compact circuitry
1 ohm stable: able to continuously power loads of 1 ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be able to perform the way they were made to
Variable subsonic filter: to prevent your subwoofer(s) from bottoming out, the variable subsonic filter filters out frequencies below the subwoofer(s) specified low frequency limits and allows the driver to reach a maximum safe excursion
Variable low-pass crossover: subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction
QUALITY - This Class D Monoblock Amplifier exhibits quality frequency response rates and crossover network which places this amp at a prominent place. Durable design and highly efficient performance makes this mono sub amp stand out amongst the others.
1 Ohm Stable - This cobalt subwoofer amplifier for car speakers is able to power loads of 1 Ohm on a continuous basis without facing any difficulties like overheating, making extra sounds. This Class D amplifier is designed to power subwoofers that have a constant demand of high power in order to operate effectively.
Low/High Level Inputs – The monoblock subwoofer amplifier for car stereo speakers with mosfet power supply comes with low/high level inputs. A low level (RCA) input is measured in voltages. A high level (+/- wire) input is measured in wattages. Both essentially carry signal from your receiver to your amplifier to your speakers
Features – The monoblock bass boost amplifier has features like - Frequency Response: 10~250HZ, Low Pass Filter, Bass Boost, Subsonic Control, Remote Bass Knob, MOSFET Power Supply, Thermal Protection, Phase Shift
Power – This Class D 3000 watt Amplifier has a power rating distribution as followed 3000 X 1 MAX @ 1 OHM. The monoblock amplifier for car speakers also provides a 2-way protection circuitry as a part of its design.
1 OHM STEREO: 1-ohm stable monoblock operation for MAX power
DOUBLE POWER Bridge 2 monoblocks together for double power
MOSFET POWER SUPPLY: Military-grade PCB with PWM MOSFET power supply
OVERLOAD CIRCUIT PROTECTION: Direct short, thermal, and overload circuit protection
SPECIFICATIONS: High/speaker level and low level/RCA input; 4g power wire and 8g speaker wire outputs; Variable 12dB high and low pass crossovers; 12dB bass boost increases low octave harmonics; Dimensions (L x W x H): 16.25 x 8.75 x 4 inches; Weight: 8.22 pounds
Power - 3400 Watts Max x 1 @1-Ohm, 1700 Watts Max x 1 @2-Ohms, 850 Watts Max x 1 @4-Ohms
Class D - Power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until it’s needed instead of being converted into heat. Reduction in size/weight, reduced power waste, smaller heat sink, compact circuitry
1 Ohm Stable - Able to continuously power loads of 1 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be able to perform the way they were made to
Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry
Strapping Capable - You are able to strap two R3400D amplifiers and double the power that is being sent to your subwoofer(s). You now have the ability to connect more subwoofers to take advantage of the extra power